admin
Forum Management
Posts: 1,149
|
Post by admin on May 14, 2010 6:28:53 GMT -6
Now that I'm armed with photography again, I'd like to share a few of my more interesting "failures". Todays subjects are two vessels. One is red oak, the other, I think, is Elm. I won't bother with the whole vessels, just the part that's more interesting. We've all seen bowls before. The first pic of of some spalling on the outer flare of the red oak bowl. It's got a lot of swirl between the two punky spots. (Wish I knew how to turn punky into useable, only two little spots, but it was enough to junk the bowl for.) This bowl is sitting on my desk as a convenient candy bowl for my peppermints, so it's not a complete loss. This second pic is of the same area, only much closer to really show the detail in the swirl. If it hadn't have been for the punky, I'm pretty sure this vessel might have sold for me. Great swirl and, suprisingly, the swirled grain is actually glass smooth. The last pic of the failures is this bark inclusion on an elm bowl. The inclusion has darkened a little over time. When I first turned it, the bark was a vivid orange with the speckling on each side of the inclusion being almost stark white. As you can see, it's changed considerably. As of now, this one sits on my dresser for loose change. Both the blanks that produced these vessels were plain and ordinary, which is often the case. Both pieces were taken from my wood supply for the winter.
|
|
|
Post by Ruffnek on May 14, 2010 9:03:17 GMT -6
Whaddaya mean failures?
Just a little thin CA on those punky areas of the Red Oak bowl and after sanding, it's perfect.
The Elm bowl isn't near as nice. I've turned them with the bark left onone spot like that and yes, it darkens over time.
I certainly wouldn't call either one a failure, though, especialy that Oak.
|
|
sawduster
Moderator
The Motley Crew
Posts: 1,831
|
Post by sawduster on May 14, 2010 12:07:52 GMT -6
I agree with Cody, there's lots that can be done to fill those voids. I like to fill in voids like that by sprinkling some wood flour (very fine sanding dust) then drip on some CA. Overfill the voids, then sand down smooth. If they're not real bad, you could also use shellac to fill them, then proceed with your regular finish.
Certainly not failures as far as I'm concerned. I don't think I'd throw away all the work put into them thus far over that little bitty issue.
|
|
|
Post by sdb777 on May 14, 2010 18:54:07 GMT -6
Guess I don't know exactly what to look at.....I didn't see anything wrong with those items? And you told me where to look too!
I would think that any 'natural' product is always going to have a 'problem area', but that's part of the beauty in it to begin with. Now if you were dealing with a big chunk of plastic(eck!).....
Scott (super gloss 'em and charge double) B
|
|
Mark
WoW Member
I sure enjoy wood-chip showers!
Posts: 139
|
Post by Mark on May 14, 2010 20:43:51 GMT -6
TJ,
No way would I consider those "failures". They still have bottoms that will keep the contents in. They exhibit the natural wonderment of the stuff most people just refer to as wood. Finish 'em up and put 'em on your for sale table.
Mark
|
|
|
Post by mcbryde on May 16, 2010 11:05:20 GMT -6
TJ,
It looks to me like you don't know what a failure is, LOL.
E
|
|
|
Post by RiverWalker on May 16, 2010 11:29:43 GMT -6
I agree with the others, while these are not perfect for a certain style, I am sure that many would find these defects to be a different sort of charm in a good way.
|
|
admin
Forum Management
Posts: 1,149
|
Post by admin on May 16, 2010 13:56:43 GMT -6
I strive to match guys like Cody, Les, Bood, Doug, and others. When one compares my work (poorly finished, very little sheen, obvious flaws), I'm not even within shouting distance of them. I guess I won't be happy until I match some of these guys step for step.
|
|
monty
WoW Member
Posts: 147
|
Post by monty on May 17, 2010 7:06:24 GMT -6
Those "flaws" are what gives it character and makes it a unique one-of-a kind bowl. And ditto on the CA in the punky areas. When I get close to the final size, I apply thin CA liberally, let it soak in and then continue turning, repeating if necessary.
|
|