|
Post by boodrow on Jan 27, 2010 14:23:27 GMT -6
Im thinkin bout buyin a digital degree gauge , my crapsman table saw degree index is off about 2 degrees. Does anyone have one of these , if so do u recomend it or is it piece of chit? Boodrow
|
|
Gecko
WoW Member
Posts: 180
|
Post by Gecko on Jan 27, 2010 15:51:54 GMT -6
I have one and it works quite well. That is until the battery died and I haven't replaced it. Since I usually only cut 45* and 90*, I find my 45/45/90 aluminum triangle gets me just as close. That being the case, I guess if you do more than those two angles, I would recomend it but if not then it isn't really needed. It is not a piece of chit though.
|
|
rrich
WoW Member
Posts: 737
|
Post by rrich on Jan 27, 2010 15:57:45 GMT -6
The "Angle Boxes" as they are called are very accurate. They have but one fault.
The "On/Off" switch only turns off the display. (Which draws almost no current from the battery.) The remaining electronics are alive and well. What this means is that the battery goes dead in about 6 months,
I always remove the battery from mine when not in use.
|
|
|
Post by boodrow on Jan 27, 2010 16:13:35 GMT -6
Thanks for the replys , Gecko u talk about a 45,45,90 aluminum device , is it a speed square , home made or store bought? I mite be interested in one of those. Thanks Boodrow
|
|
Beamer
Forum Management
Posts: 1,176
|
Post by Beamer on Jan 27, 2010 19:36:28 GMT -6
I'm not a fan of the angle boxes - i have a Beall Tilt Box and i hardly ever use the dang thing. It's touchy as heck and only works with gravity so it's more limited than my chosen device. I really really LOVE this: www.amazon.com/dp/B001PTGBSAI use it nearly everytime i'm out in the shop. It's way more versatile than the gravity-dependant boxes.
|
|
Gecko
WoW Member
Posts: 180
|
Post by Gecko on Jan 28, 2010 13:54:50 GMT -6
Boodrow I have no idea of what it actual is meaning stroe bought or homemade. It is basically a 1/8" thick aluminum 45/45/90 square like a drafting square with no markings on it. I think it is about 9" long on the legs. It was in my wifes grandfathers tool chest I recieved when he passed on. He was a Boeing machinist.
|
|
|
Post by boodrow on Jan 28, 2010 15:06:53 GMT -6
Gecko , thanks for the reply , the meaning home made , or store bought is did u make it or buy it from a supplier. Wish I knew where to get my hands on one. I can think of lots of uses for it. Boodrow
|
|
Gecko
WoW Member
Posts: 180
|
Post by Gecko on Jan 28, 2010 15:13:46 GMT -6
hmmm I work is a sheet metal shop. I have the aluminum. Wonder how accurate I could make one. I think I may try.
|
|
Gecko
WoW Member
Posts: 180
|
Post by Gecko on Jan 28, 2010 15:33:06 GMT -6
Well that seemed to be pretty accurate. I will flatten the edges a bit and then get a battery for the Wixey and see how close it is. Looks dead on when up against the Starrtet protractor head but my eyes are not what they used to be.
|
|
|
Post by boodrow on Jan 29, 2010 5:33:09 GMT -6
Gecko if u make some I like to buy one from u Boodrow
|
|
Joe Lyddon
WoW Member
Banned.
Sam Maloof & I Dec. 2, 2005
Posts: 2,507
|
Post by Joe Lyddon on Jan 29, 2010 12:15:20 GMT -6
Im thinkin bout buyin a digital degree gauge , my crapsman table saw degree index is off about 2 degrees. Does anyone have one of these , if so do u recomend it or is it piece of chit? Boodrow I too like store bought 45/90 drafting triangles. They are VERY accurate... and cheap compared to other sources. I even took one and made some wooden ones that are also very handy! Got the idea from Nicki... Here is a writeup on what I did: www.ncwoodworker.net/pp/showgallery.php?cat=1352
|
|
|
Post by fredbelknap on Jan 31, 2010 8:24:44 GMT -6
I'm not a fan of the angle boxes - i have a Beall Tilt Box and i hardly ever use the dang thing. It's touchy as heck and only works with gravity so it's more limited than my chosen device. I really really LOVE this: www.amazon.com/dp/B001PTGBSAI use it nearly everytime i'm out in the shop. It's way more versatile than the gravity-dependant boxes. That looks like a handy tool. I have a Wixey and like it but there is places that it won't work such as setting the miter gauge. I put one in my cart, $45.
|
|
Beamer
Forum Management
Posts: 1,176
|
Post by Beamer on Jan 31, 2010 10:59:21 GMT -6
Fred - hold out until they go for about $30 - that's what I found mine for
|
|
|
Post by fredbelknap on Jan 31, 2010 17:26:22 GMT -6
Fred - hold out until they go for about $30 - that's what I found mine for Thanks I'll just let it ride for a few weeks, see what happens.
|
|
|
Post by boodrow on Feb 1, 2010 14:05:06 GMT -6
Thanks again for the tip , I ordered one from WoodCraft this past saturday. Was on sale till the 30th of jan for 39.95 I think it was. Anyway I got it comin. Boodrow
|
|
rrich
WoW Member
Posts: 737
|
Post by rrich on Feb 1, 2010 15:47:44 GMT -6
|
|
lexrex
Forum Management
Posts: 822
|
Post by lexrex on Feb 3, 2010 8:38:15 GMT -6
Rich, I did not know that about the internal electronics...no WONDER!
Boodrow, I use the Wixey box and I do like it. I used it for setting up my tools/fences and I use it to check them now and again for square.
Fred, you can use the box to set your miter gauge. Start with the gauge at 90* and set it on your TS table, with the runner going down the side of your saw, so it's kind of hanging there. 0 the digital gauge and then stick it to the miter bar of the miter gauge. Now you can move the miter to whatever angle you need and tighten it down!
|
|
|
Post by boodrow on Feb 3, 2010 19:08:01 GMT -6
lexrex thanks for the info , I will prob get one soon. Its always good to get input from others fore u buy it. Boodrow
|
|
|
Post by art3427 on Feb 8, 2010 9:07:35 GMT -6
I buy draftsman triangles (plastic) from Office Depot. I currently own a 45/45/90, 30/60/90 and a 22.5/67.5/90. All three of them probably cost me less than $20.00. They are super accurate.
art
|
|
|
Post by boodrow on Feb 8, 2010 20:15:03 GMT -6
Art thanks for the info , I didnt know who had these to sell. By jingos I will be goin there this comin weekend to get some of um. Thanks again Boodrow
|
|